---
title: Center of Gravity in Rigging | ILS
url: https://machinerymovingnv.com/glossary/center-of-gravity/
business: Industrial Logistics Services, Inc. (ILS)
what: machinery moving, rigging, millwright services, installation and alignment, plant relocation, machinery transport, crating, storage
phone: (775) 882-3319
fax: (775) 882-2693 (fax only)
email: johns@ilsmachinerymoving.com
address: 3868 Goni Rd, Carson City, NV 89706
hours: Mon-Fri 7:00 am - 4:00 pm, Sat-Sun closed
licenses: Nevada contractor licenses 0046276, 0083124, 0083125; USDOT 642556, MC-531191
estimates: free
---

- [Home](https://machinerymovingnv.com/)
- [Glossary](https://machinerymovingnv.com/glossary/)
- Center of gravity

# Center of gravity

The center of gravity is the balance point of a load. Slings must be arranged so the hook sits above that point, or the machine tilts and swings when it leaves the floor.

Key points

- The balance point where the weight acts as one force
- Often off-center: motors, gearboxes and fluids shift it
- The hook has to sit over it or the load tips
- Manufacturer lift drawings usually mark the lifting points
- Test lifts a few inches off the floor show whether the estimate was right

Most machines are not symmetrical. A motor on one end, a heavy base casting or a half-full tank pulls the balance point away from the middle. Riggers find that point first, because it controls every other choice in the lift.

## How it is found

Manufacturer drawings and manuals often give the center of gravity or at least the lifting points. If not, the weight distribution is estimated from the machine's construction, and a short test lift shows which way the load wants to tilt. Adjusting the sling lengths or shifting the pick point brings it level.

- Read the manufacturer's lifting drawing
- Check where the heavy components sit
- Account for fluids, loose parts and attachments
- Lift a few inches, observe, adjust

## Why it changes sling choices

When the center of gravity is not midway between two lift points, the nearer sling carries more load. Rated capacities then have to be checked against the share each leg takes, not just against the total weight. Tall machines add another risk: a high center of gravity makes the load tip over in a turn or on a slope.

## How it connects to ILS work

Planning with the center of gravity is part of any lift, whether it uses forklifts from 3,000 lbs. to 100,000 lbs. with rigging booms, the 300-ton hydraulic gantry system or the 2-ton portable aluminum gantry. The more you tell us about the machine, the easier the plan. Photos of the nameplate and any lift drawing are enough to start a free estimate.

### Sources (2)

- U.S. Occupational Safety and Health Administration : [osha.gov/laws-regs/regulations/standardnumber/1926/1926.251](https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.251) (checked November 2026)
- ASME : [asme.org/codes-standards/find-codes-standards/b30-9-slings](https://www.asme.org/codes-standards/find-codes-standards/b30-9-slings) (checked November 2026)

### Send the machine details

Type, size, weight, where it is and where it is going. Photos help. Estimates are free.

[Start the estimate](#estimate)

### Related

- [Sling angle](https://machinerymovingnv.com/glossary/sling-angle/)
- [Spreader bar](https://machinerymovingnv.com/glossary/spreader-bar/)
- [Rigging](https://machinerymovingnv.com/glossary/rigging/)
- [Lift planning basics for plant managers](https://machinerymovingnv.com/guides/lift-planning-basics/)
- [Machine measuring worksheet](https://machinerymovingnv.com/tools/machine-measure-worksheet/)

## Questions we hear

[All questions](https://machinerymovingnv.com/faq/)

### Is the center of gravity always in the middle?

No. Motors, drives, tanks and cast bases move it to one side or toward the top, so it must be checked for each machine.

### Can the center of gravity change during a move?

Yes. Fluids shift, parts are removed and a load that is tipped or turned has a different balance than one standing upright.
