---
title: Spreader Bar: Definition and Use | ILS
url: https://machinerymovingnv.com/glossary/spreader-bar/
business: Industrial Logistics Services, Inc. (ILS)
what: machinery moving, rigging, millwright services, installation and alignment, plant relocation, machinery transport, crating, storage
phone: (775) 882-3319
fax: (775) 882-2693 (fax only)
email: johns@ilsmachinerymoving.com
address: 3868 Goni Rd, Carson City, NV 89706
hours: Mon-Fri 7:00 am - 4:00 pm, Sat-Sun closed
licenses: Nevada contractor licenses 0046276, 0083124, 0083125; USDOT 642556, MC-531191
estimates: free
---

- [Home](https://machinerymovingnv.com/)
- [Glossary](https://machinerymovingnv.com/glossary/)
- Spreader bar

# Spreader bar

A spreader bar is a steel beam that rides above a load and keeps the slings pulling straight up. It protects wide or delicate machines from the squeeze that angled slings create.

Key points

- Keeps sling legs vertical
- Takes the inward force on itself
- Protects tanks, cabinets and wide machines
- Has its own rated capacity that must be marked
- Belongs to the family of below-the-hook lifting devices

Angled slings push inward on whatever they lift. That is fine for a solid casting and a problem for a thin-walled tank, a control cabinet or a machine with an overhanging cover. A spreader bar takes the sideways force and lets the load see only a vertical pull.

## Spreader bar versus lifting beam

The two look alike. A spreader bar works in compression, with slings running from its ends down to the load. A lifting beam works in bending, with a hook at the center and lifting points below. Both are covered by the ASME B30 series of standards for below-the-hook devices, and both carry a nameplate with the rated load.

Spreader bar versus lifting beam Device Main force Typical use

Spreader bar Compression Wide loads on two or more slings

Lifting beam Bending Straight pulls with a center hook

## When a rigger reaches for one

- The load cannot take inward sling force
- Lift points are too far apart for the slings to reach steeply
- Headroom is limited and angles would be too flat
- A long, thin object needs more than one pick point

## Where ILS comes in

Rigging, slings, hoists and more are on ILS's published list of equipment, and the crew plans each lift with the load's weight, balance and lift points in hand. Whether one is used on your machine depends on the machine, and the estimate covers that.

### Sources (3)

- ASME : [asme.org/codes-standards/find-codes-standards/b30-9-slings](https://www.asme.org/codes-standards/find-codes-standards/b30-9-slings) (checked November 2026)
- U.S. Occupational Safety and Health Administration : [osha.gov/laws-regs/regulations/standardnumber/1926/1926.251](https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.251) (checked November 2026)
- U.S. Occupational Safety and Health Administration : [osha.gov/laws-regs/regulations/standardnumber/1926/1926.1404](https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.1404) (checked November 2026)

### Send the machine details

Type, size, weight, where it is and where it is going. Photos help. Estimates are free.

[Start the estimate](#estimate)

### Related

- [Sling angle](https://machinerymovingnv.com/glossary/sling-angle/)
- [Working load limit](https://machinerymovingnv.com/glossary/working-load-limit/)
- [Center of gravity](https://machinerymovingnv.com/glossary/center-of-gravity/)
- [Industrial rigging](https://machinerymovingnv.com/services/rigging/)
- [Rigging, slings, hoists & tools](https://machinerymovingnv.com/equipment/rigging-gear/)

## Questions we hear

[All questions](https://machinerymovingnv.com/faq/)

### Does a spreader bar need a rating?

Yes. Like any lifting device, it must carry a marked rated load and be used within it.

### Does a spreader bar change the sling angle?

Yes. It spreads the lift points while keeping the sling legs vertical, so the legs carry close to their share instead of a higher one.
