---
title: Rigging Gear and How It Is Inspected | ILS Guide
url: https://machinerymovingnv.com/guides/rigging-gear-and-inspection/
business: Industrial Logistics Services, Inc. (ILS)
what: machinery moving, rigging, millwright services, installation and alignment, plant relocation, machinery transport, crating, storage
phone: (775) 882-3319
fax: (775) 882-2693 (fax only)
email: johns@ilsmachinerymoving.com
address: 3868 Goni Rd, Carson City, NV 89706
hours: Mon-Fri 7:00 am - 4:00 pm, Sat-Sun closed
licenses: Nevada contractor licenses 0046276, 0083124, 0083125; USDOT 642556, MC-531191
estimates: free
---

- [Home](https://machinerymovingnv.com/)
- [Guides](https://machinerymovingnv.com/guides/)
- Rigging gear and how it is inspected

# Rigging gear and how it is inspected

Rigging gear is inspected before use, every time, by someone qualified to spot damage, and anything defective comes out of service. Slings must carry their rated capacity, hardware must be marked, and the load, angles and attachment points decide what gear is chosen.

Key points

- Slings, shackles, hooks and hoists are inspected before use
- Rated capacity must be legible and never exceeded
- Sling angle changes the load on each leg, sometimes sharply
- Damaged gear is removed from service, not patched
- 'Qualified' is the employer's determination, not a card OSHA issues

Rigging failures are rare, and nearly all begin with gear that was damaged, overloaded or used at a bad angle. The rules below come from OSHA and from the ASME B30 standards, which we cite by name only. We describe what they require and what the owner and the rigger each have to do. This guide describes what the rules and standards say.

## The gear in a machinery lift

Common items include wire rope, chain and synthetic slings; shackles, hooks and eye bolts; hoists and chain falls; spreader and lifting beams; jacks, skates and rollers; and gantries. ILS publishes its own list as rigging, slings, hoists and a large inventory of power and hand tools, with a 2-ton portable aluminum gantry and a 300-ton hydraulic gantry system. The gear is chosen from the load and the plan, not by habit.

## What the rules say

For general industry, OSHA 29 CFR 1910.184 covers slings: each sling is inspected before use, carries its rated capacity identification, and damaged slings are removed from service. For construction, 29 CFR 1926.251 sets similar rules for rigging equipment, including a safe working load marking and inspection before each shift. ASME's B30 volumes cover slings (B30.9), rigging hardware (B30.26) and jacks and gantries (B30.1) in more detail.

Nevada operates its own OSHA state plan through the Division of Industrial Relations and adopts the federal standards by reference, so the same rules apply in Nevada.

## A pre-use inspection checklist

- Read the identification tag or marking and confirm the capacity is readable.
- Check for cuts, fraying, broken wires, kinks, crushing or heat damage on rope and synthetic slings.
- Check chain links for stretch, gouges, twist or bent links.
- Inspect shackles, hooks and eyes for deformation, cracks, wear and a working latch.
- Check that pins and bolts are the right type, seated and secured.
- Confirm no knots, and no sharp edges against the sling without padding.
- Tag and remove anything doubtful from service.

## Why angle matters

A sling's rated capacity is stated for a given angle. As the legs spread toward a flatter angle, tension rises in each leg. That is why the lift plan includes a sketch of the rigging, not just the weight. Choosing a longer sling or a spreader beam often solves the problem.

Why angle matters Sling angle from horizontal Effect on each leg

90 degrees (vertical) Tension equals its share of the load

60 degrees Modestly higher than vertical

45 degrees Substantially higher than vertical

30 degrees Roughly double its share of the load, so avoid

## What the owner should expect to see

On site, you should see slings with legible tags, hardware matched to the load, padding where slings meet edges, and a clear zone beneath the lift. If a rigger shows you a sling with a missing tag or visible damage, the right response is that it is set aside. Ask questions freely; a good crew treats them as normal.

## Who is qualified

OSHA's construction rules require a qualified rigger for hoisting work where employees are in the fall zone and during assembly, and they leave the determination of who is qualified to the employer (29 CFR 1926.1425(c)(3) and 1926.1404(r)(1)). OSHA does not issue rigger cards. When you hire, ask how the contractor trains and evaluates its riggers; see [how to choose a rigging contractor](https://machinerymovingnv.com/guides/choosing-a-rigging-contractor/).

Powered industrial trucks, including forklifts with rigging booms, require operator training and evaluation under 29 CFR 1910.178. See [our rigging equipment](https://machinerymovingnv.com/equipment/rigging-gear/) and [lift planning basics](https://machinerymovingnv.com/guides/lift-planning-basics/).

### Sources (4)

- U.S. Occupational Safety and Health Administration : [osha.gov/laws-regs/regulations/standardnumber/1910/1910.184](https://www.osha.gov/laws-regs/regulations/standardnumber/1910/1910.184) (checked November 2026)
- U.S. Occupational Safety and Health Administration : [osha.gov/laws-regs/regulations/standardnumber/1926/1926.251](https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.251) (checked November 2026)
- Electronic Code of Federal Regulations : [ecfr.gov/current/title-29/part-1926/subpart-CC](https://www.ecfr.gov/current/title-29/part-1926/subpart-CC) (checked November 2026)
- ASME : [asme.org/codes-standards/find-codes-standards/b30-9-slings](https://www.asme.org/codes-standards/find-codes-standards/b30-9-slings) (checked November 2026)

### Send the machine details

Type, size, weight, where it is and where it is going. Photos help. Estimates are free.

[Start the estimate](#estimate)

### Licensed in Nevada

Nevada State Contractors Board licenses 0046276 (C-33 Installing Industrial Machinery), 0083124 (A-14, A-20) and 0083125 (C-14I Rigging and Cranes, C-14J Conveyance of Goods). USDOT 642556, MC-531191.

[What the classes cover](https://machinerymovingnv.com/guides/nevada-contractor-license-classes/)

### Keep reading

- [Rigging, slings, hoists & tools](https://machinerymovingnv.com/equipment/rigging-gear/)
- [Lift planning basics for plant managers](https://machinerymovingnv.com/guides/lift-planning-basics/)
- [Industrial rigging](https://machinerymovingnv.com/services/rigging/)
- [How to choose a rigging contractor](https://machinerymovingnv.com/guides/choosing-a-rigging-contractor/)
- [2-ton portable aluminum gantry](https://machinerymovingnv.com/equipment/portable-gantry/)

## Questions we hear

[All questions](https://machinerymovingnv.com/faq/)

### How often should rigging gear be inspected?

Before use, as OSHA requires, with periodic documented inspections as the ASME B30 standards describe. The user checks it each time it goes on a load.

### Can a damaged sling be repaired?

Generally not by the user. Follow the maker's guidance; repairs to alloy chain and hardware are for the manufacturer or a qualified person.

### Does OSHA certify riggers?

No. OSHA leaves the question of who is qualified to the employer, which makes the contractor's training process worth asking about.
