---
title: Machine Measuring Worksheet | ILS Carson City
url: https://machinerymovingnv.com/tools/machine-measure-worksheet/
business: Industrial Logistics Services, Inc. (ILS)
what: machinery moving, rigging, millwright services, installation and alignment, plant relocation, machinery transport, crating, storage
phone: (775) 882-3319
fax: (775) 882-2693 (fax only)
email: johns@ilsmachinerymoving.com
address: 3868 Goni Rd, Carson City, NV 89706
hours: Mon-Fri 7:00 am - 4:00 pm, Sat-Sun closed
licenses: Nevada contractor licenses 0046276, 0083124, 0083125; USDOT 642556, MC-531191
estimates: free
---

- [Home](https://machinerymovingnv.com/)
- [Guides](https://machinerymovingnv.com/guides/)
- Machine measuring worksheet

# Machine measuring worksheet

Use the worksheet to record a machine's length, width, height, weight and lift points, and the doors, floors and clearances along its route. With those numbers, ILS can choose the lift, the trailer and the method for a free estimate.

Key points

- Measure length x width x height at the widest, longest and tallest points
- Find the weight on the nameplate, in the manual or from the maker
- Photograph lift points, fork pockets and anything that sticks out
- Measure doors, aisles and ceiling height along the route
- Ask us if you are unsure; estimates are free

The measurements you send do more to shape an estimate than anything else. They decide which forklift or gantry applies, which trailer carries the load and whether a permit is needed. Take a few minutes with a tape measure and your phone, and fill in the worksheet.

## Step by step

- Length: the longest side, including handles, covers and anything that extends
- Width: the widest point, including side panels and operator stations
- Height: from the floor to the highest point, including lights and stacks
- Weight: look for a nameplate or serial plate on the machine; if there is none, the manual or the maker's data sheet will have it
- Lift points: note eyebolts, lugs, fork pockets and forklift slots, and photograph them
- Floor: write down what the machine sits on, and whether it is bolted down
- Route: measure door widths and heights, aisle widths, ceiling height and floor type from the machine to the dock

## Why each number matters

- Length, width and height set the trailer and whether the move needs a permit; see the [oversize load checker](https://machinerymovingnv.com/tools/oversize-load-checker/)
- Weight sets the lifting gear: [forklifts with rigging booms](https://machinerymovingnv.com/equipment/rigging-forklifts/), a gantry or skates
- Lift points tell the crew where slings go
- Door and aisle sizes decide whether a machine goes through whole or has to be partly taken down
- Floor condition decides what can roll over it and what needs plates

## Common mistakes

The most common errors are measuring only the machine body and missing a tall stack or light, using a weight from an older model, and forgetting the pallet or skid under the machine. If a machine will travel on a skid or crate, measure that as well. Also look up: sprinkler lines, ducts and lights often limit the height more than a door does.

Our guide on [how to measure a machine for a moving estimate](https://machinerymovingnv.com/guides/how-to-measure-a-machine/) goes into more detail.

## What to do with the worksheet

Send us the numbers and the photos with a request for a [free estimate](https://machinerymovingnv.com/free-estimate/). Partial information is fine; we will ask for what else we need. A site visit can follow where the move is complex.

### Sources (3)

- U.S. Occupational Safety and Health Administration : [osha.gov/laws-regs/regulations/standardnumber/1926/1926.251](https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.251) (checked November 2026)
- Nevada Legislature : [leg.state.nv.us/nrs/nrs-484d.html](https://www.leg.state.nv.us/nrs/nrs-484d.html) (checked November 2026)
- ASME : [asme.org/codes-standards/find-codes-standards/b30-9-slings](https://www.asme.org/codes-standards/find-codes-standards/b30-9-slings) (checked November 2026)

### Send the machine details

Type, size, weight, where it is and where it is going. Photos help. Estimates are free.

[Start the estimate](#estimate)

### Licensed in Nevada

Nevada State Contractors Board licenses 0046276 (C-33 Installing Industrial Machinery), 0083124 (A-14, A-20) and 0083125 (C-14I Rigging and Cranes, C-14J Conveyance of Goods). USDOT 642556, MC-531191.

[What the classes cover](https://machinerymovingnv.com/guides/nevada-contractor-license-classes/)

### Related

- [How to measure a machine for a moving estimate](https://machinerymovingnv.com/guides/how-to-measure-a-machine/)
- [What should I send for an estimate?](https://machinerymovingnv.com/faq/what-to-send-for-an-estimate/)
- [Free estimate](https://machinerymovingnv.com/free-estimate/)
- [Nevada oversize load checker](https://machinerymovingnv.com/tools/oversize-load-checker/)
- [Forklifts with rigging booms (3,000 to 100,000 lbs.)](https://machinerymovingnv.com/equipment/rigging-forklifts/)

## Questions we hear

[All questions](https://machinerymovingnv.com/faq/)

### What if I do not know the weight?

Send the make and model from the nameplate and a photo. If there is no nameplate, we can help work out the weight from the size and type, then confirm it before a lift.

### Do I need to measure everything?

Measure what you can. Machine size, weight and photos are the most important.

### Is the worksheet only for large machines?

No. It works for any machine, large or small.
