Compressor moving and rigging
An air compressor is moved by depressurizing the system, disconnecting the piping and power, lifting the package from its base, and bolting it down on a flat floor. ILS holds a Nevada C-33 Installing Industrial Machinery license, so the same company that rigs the compressor can set and level it.
- Nevada Contractors License 46276
- USDOT 642556 · our own trucks
- 4.6 on Google (15 reviews)
Key points
- The system is depressurized and locked out before anything is disconnected
- Rotary screw packages lift from the base frame; piston units are heavy at the crankcase
- Receiver tanks are pressure vessels and are moved empty
- Piping and drains are tagged and photographed before they come apart
- Free estimates from the nameplate and a photo of the layout
Compressors are the quiet workhorse of a plant, and a relocation touches more than the machine itself. The receiver tank, dryer, filters and the piping between them are all part of the job. A compressed-air system that is moved without a plan can leave the plant without air until it is rebuilt.
The compressor is a system
Most plants have a compressor, a receiver tank, a dryer, filters, a condensate drain and a network of pipe. Moving only the compressor leaves the rest. We ask what moves with it so that the plan covers the whole package, and our disconnect and reconnect coordination covers who disconnects what.
Small piston compressors on a tank are moved on a pallet jack or forklift. Large rotary screw packages weigh in the thousands of pounds and have a steel base with lifting points or fork pockets. Two-stage piston compressors are heavier in the crankcase and need a lift plan like any other single piece of machinery.
Safe shutdown first
Stored air is stored energy. Before a compressor is moved, the system is shut down, the air is bled from the receiver and the lines, and the electrical supply is locked out under the plant's lockout/tagout procedure (29 CFR 1910.147). Receiver tanks are pressure vessels, and the moving crew treats them as such: they are moved empty and the valves and gauges are protected.
- Shut down and lock out the motor starter
- Bleed the receiver and the air lines to zero
- Drain lube oil per the manufacturer if the package will be tilted or hauled
- Cap open ports and fittings so dirt stays out
- Photograph and tag every pipe and wire before it comes off
Lifting and setting
A compressor package that sits on isolators or on the floor is lifted by a forklift under the base or by slings through the lifting points. A boom on a forklift lets us lift above a dock or over a low obstacle. Once it is placed, the machine is leveled and the anchors set according to the manufacturer. A leveled, solid floor reduces vibration and noise and keeps oil circulating correctly.
- Confirm the weight and the lift points from the nameplate or manual
- Disconnect and cap the air, drain and cooling lines
- Lift and move the package
- Set on the new floor and check level
- Reconnect the piping and power as agreed in the estimate
- Leave the owner to start the system and test for leaks
What to send
Send the nameplate, the horsepower if known, the approximate weight and size, photos of the machine and the receiver, and the route to the new location. Tell us if the dryer and receiver come too. We give free estimates, and a single compressor is as welcome as a whole shop.
Sources (4)
- U.S. Occupational Safety and Health Administration: osha.gov/laws-regs/regulations/standardnumber/1910/1910.147 (checked November 2026)
- U.S. Occupational Safety and Health Administration: osha.gov/laws-regs/regulations/standardnumber/1910/1910.184 (checked November 2026)
- U.S. Occupational Safety and Health Administration: osha.gov/laws-regs/regulations/standardnumber/1910/1910.178 (checked November 2026)
- Nevada Legislature: leg.state.nv.us/nrs/nrs-484d.html (checked November 2026)
Send the machine details
Type, size, weight, where it is and where it is going. Photos help. Estimates are free.
Start the estimateLicensed in Nevada
Nevada State Contractors Board licenses 0046276 (C-33 Installing Industrial Machinery), 0083124 (A-14, A-20) and 0083125 (C-14I Rigging and Cranes, C-14J Conveyance of Goods). USDOT 642556, MC-531191.
What the classes coverCan you move a compressor and its air receiver together?
Yes, though the receiver is moved empty and depressurized. Large receivers are often the heaviest part of the job, so we ask for the tank's data plate.
Do you reconnect the air piping?
ILS coordinates the reconnect with the plant's maintenance staff or a piping contractor. ILS also holds the A-20 Industrial Piping classification (license 0083124).
Do I need a permit to haul a compressor?
Only if the load on the trailer exceeds Nevada's legal height, width, length or weight. Most compressors do not; the oversize rules are in NRS 484D.
Free estimates
Tell us what needs moving.
Free estimates on every job, big or small. Call the office or send the machine details and we will call you back.
(775) 882-3319Monday to Friday, 7:00 am to 4:00 pm. Fax (775) 882-2693.
- Nevada Contractors License 46276
- USDOT 642556 · our own trucks
- Carson City since 1999
- 4.6 on Google (15 reviews)
