Moving woodworking and cabinet machinery
Woodworking machinery is moved by disconnecting dust collection and power, removing blades and loose parts, lifting each machine from its base and re-leveling it at the new shop. ILS moves cabinet shops with forklifts from 3,000 lbs. to 100,000 lbs. with rigging booms.
- Nevada Contractors License 46276
- USDOT 642556 · our own trucks
- 4.6 on Google (15 reviews)
Key points
- Blades, cutterheads and knives are removed or locked
- Dust collection ducts and filter housings are disconnected and labeled
- Long beds and fences are supported in transit
- Tall dust collectors and cyclones are handled as tall loads
- Single machines and whole shops welcome
- Free estimates
Cabinet and wood shops depend on panel saws, edgebanders, CNC routers, drum sanders, planers and dust collection. These machines range from a few hundred pounds to several tons. Industrial Logistics Services lists Cabinet and Woodworking Facilities among the industries it works with.
A mix of delicate and heavy
A shop floor of woodworking machinery includes both light and heavy items. Sliding table saws have precise carriages that must not be bumped. Wide belt sanders and planers have heavy cast beds. A CNC router has a gantry and a vacuum table. Dust collectors and cyclones are tall, thin-walled and awkward to lift.
Because wood shops often work in tight buildings with narrow doors, the path out is as important as the lift. Pallet jacks, skates and a small forklift are used for tight aisles, and larger pieces go through a dock door.
Preparation
Electrical power and any pneumatic supplies are locked out and disconnected by the shop (29 CFR 1910.147). OSHA's woodworking machinery requirements are in 29 CFR 1910.213, which covers guards and safeguards the shop already keeps. Before the move:
- Disconnect power, compressed air and dust collection
- Remove saw blades, cutterheads, knives and bits and store them in labeled cases
- Lock carriages, sliding tables and fences in the transit position
- Empty dust bins and clean out the machine to reduce weight
- Remove loose tables, extension wings and guards and bundle them
- Photograph the setup before disassembly
Rigging and hauling
Heavy planers, sanders and CNC routers are lifted with a forklift fitted with a rigging boom or placed on machinery skates. Dust collectors are moved with the inlet and outlet covered, and may need to travel on their side, so the rigger checks the maker's guidance. Equipment from a small shop can often travel on one trailer; a larger shop moves on several. The equipment trailers run to 50 tons.
ILS also offers skidding and crating for machines that will wait in storage. ILS also offers up to 25,000 square feet of indoor storage and 5 acres of outside storage.
Setting up and restarting
Once machines are placed, they are leveled and anchored where the maker requires, and power is reconnected as agreed in the estimate. Dust collection ducts must be reinstalled before the machines can run. Many shops hire a duct installer, and ILS coordinates the order of the work so machines are set where the ductwork will reach them.
Estimate checklist
Send a list of the machines with the maker, model and rough weight, photos of the shop and the doors, and the new address. Estimates are free.
Sources (3)
- U.S. Occupational Safety and Health Administration: osha.gov/laws-regs/regulations/standardnumber/1910/1910.213 (checked November 2026)
- U.S. Occupational Safety and Health Administration: osha.gov/laws-regs/regulations/standardnumber/1910/1910.147 (checked November 2026)
- U.S. Occupational Safety and Health Administration: osha.gov/laws-regs/regulations/standardnumber/1910/1910.178 (checked November 2026)
Send the machine details
Type, size, weight, where it is and where it is going. Photos help. Estimates are free.
Start the estimateLicensed in Nevada
Nevada State Contractors Board licenses 0046276 (C-33 Installing Industrial Machinery), 0083124 (A-14, A-20) and 0083125 (C-14I Rigging and Cranes, C-14J Conveyance of Goods). USDOT 642556, MC-531191.
What the classes coverDo you move cabinet shops?
Yes. Cabinet and woodworking facilities are one of the industries ILS works with.
Can you move a dust collector?
Yes. They are tall loads, so the rigger plans how to lift and carry them. The plant's ductwork contractor handles the pipe.
Do you move one machine for a small shop?
Yes. Single machines are welcome.
Free estimates
Tell us what needs moving.
Free estimates on every job, big or small. Call the office or send the machine details and we will call you back.
(775) 882-3319Monday to Friday, 7:00 am to 4:00 pm. Fax (775) 882-2693.
- Nevada Contractors License 46276
- USDOT 642556 · our own trucks
- Carson City since 1999
- 4.6 on Google (15 reviews)
