Guides to moving and rigging machinery
Nevada needs an NDOT permit for loads over 14 feet high, 102 inches wide or 70 feet long, and a licensed contractor to install machinery permanently attached to a building. These guides explain those rules and how a machinery move is measured, planned, rigged and leveled, with the public source for each.
- Nevada Contractors License 46276
- USDOT 642556 · our own trucks
- 4.6 on Google (15 reviews)
All pages in this section
How a machinery move works, step by step
A machinery move runs in seven stages: estimate, site survey, planning, disconnect and lockout, rigging and loading, transport, and setting and leveling at the new...
Read moreHow to measure a machine for a moving estimate
Measure the machine's overall length, width and height at its extreme points, find its weight on the nameplate or manual, and note where it can be lifted. Then...
Read moreHow to prepare a machine before the riggers arrive
Before the crew arrives, lock out the machine, have utilities disconnected, drain or secure fluids, tie down or remove loose parts, and photograph and label...
Read moreLockout/tagout before a machinery move
Before a machine is serviced, disconnected or lifted, the employer who owns it must isolate every energy source, lock or tag it, relieve stored energy and verify the...
Read moreLift planning basics for plant managers
A lift plan states what is being lifted, how much it weighs, how it will be rigged, what equipment will do the lifting, where it will travel and who is responsible...
Read moreNevada oversize load permits explained
In Nevada a load that exceeds 14 feet in height, 70 feet in combination length or 102 inches in width needs a permit from the Nevada Department of Transportation, as...
Read moreWhen a Nevada oversize load needs pilot cars
Under NAC 484D.670, a lead pilot car is required for loads over 15 feet 6 inches high, over 12 feet wide on a two- or three-lane highway or in darkness or holiday...
Read moreMoving machinery from Nevada into California
A machine moving from Nevada into California travels under the carrier's federal authority, and an oversize or overweight load also needs a Caltrans transportation...
Read moreNevada contractor license classes for machinery work
In Nevada, a company that contracts to install industrial machinery or to do rigging work for a fee generally needs a license from the State Contractors Board in a...
Read moreHow to choose a rigging contractor
Choose a rigging contractor on evidence you can check: an active Nevada license in the right class, a written scope, a lift plan for your machine, and a crew that...
Read morePlanning a plant relocation
Plan a plant relocation backward from the day production must restart, and sequence machines so the ones you need first are installed first. Most of the work happens...
Read moreFloor loads, anchors and machine foundations
A floor can carry a machine if its rated load covers the machine's weight on the footprint it actually bears on, and an engineer decides that, not the mover. Machines...
Read moreHow machines are leveled and aligned
A machine is leveled by setting it on shims or leveling feet and measuring from machined reference surfaces until the readings fall within the maker's tolerance....
Read moreCrating machinery for shipping
Crate machinery when it will travel a long way, be handled several times or sit in storage; skid it when it needs a short trip on a truck. A good crate immobilizes...
Read moreStoring machinery long term
To store a machine for months, keep it dry, support it on a firm surface, protect bare steel, and write down its condition before it goes in. Indoor storage is better...
Read moreRigging gear and how it is inspected
Rigging gear is inspected before use, every time, by someone qualified to spot damage, and anything defective comes out of service. Slings must carry their rated...
Read moreNorthern Nevada manufacturing by county and ZIP
Washoe County has the most manufacturing establishments in Northern Nevada, 466 in the Census Bureau's 2023 County Business Patterns, followed by Carson City with...
Read moreNevada legal load limits and permit triggers
A load in Nevada can travel without an over-dimensional permit up to 14 feet high, 70 feet long as a combination, and 102 inches wide, within the federal 80,000-pound...
Read moreNevada oversize load checker
Enter the height, width, length and weight of a loaded trailer, and the checker compares them with Nevada's legal limits to show whether the load likely needs an...
Read moreMachine measuring worksheet
Use the worksheet to record a machine's length, width, height, weight and lift points, and the doors, floors and clearances along its route. With those numbers, ILS...
Read moreKey points
- Start with the move guide if this is your first machinery relocation
- Measuring and preparing a machine are the two jobs that most often belong to the owner
- Lockout and lift planning explain who does what on the day
- Nevada permit and pilot car guides cite the actual NRS and NAC sections
Industrial Logistics Services writes these for plant managers, maintenance supervisors, shop owners and contractors who have a machine to move and want to know what a good job looks like. Every rule is cited to its public source so you can read the original yourself. For a quote on your own machine, the estimate is free.
Planning a move
If you have never moved a production machine, begin with how a machinery move works. It walks through the job from the first call to the final leveling. Then use how to measure a machine and how to prepare a machine before the riggers arrive to get your own part of the work done.
- Measuring a machine: length, width, height, weight, lift points and doors
- Preparing a machine: fluids, loose parts, covers, anchors and photos
- The sequence of a move, from estimate to set and level
Safety on the day of the move
Two guides cover the safety side. Lockout/tagout before a machinery move describes what OSHA 1910.147 requires and why the plant, not the mover, controls the energy sources. Lift planning basics for plant managers explains what goes into a plan for a heavy lift and what the ASME standards say about it.
Hauling the load on the road
Once a machine is on a trailer it becomes a highway question. Nevada oversize load permits explained covers the height, length and width limits and the permit types. When a Nevada oversize load needs pilot cars lists the triggers for lead and rear escort vehicles, and moving machinery from Nevada into California covers the state line.
More guides
Other guides in this library cover Nevada contractor license classes, how to choose a rigging contractor, planning a plant relocation, floor loads and foundations and how machines are leveled. For quick answers see the questions and answers page, and for measuring help use the machine measuring worksheet.
Sources (3)
- Nevada Legislature: leg.state.nv.us/nrs/nrs-484d.html (checked November 2026)
- U.S. Occupational Safety and Health Administration: osha.gov/laws-regs/regulations/standardnumber/1910/1910.147 (checked November 2026)
- ASME: asme.org/codes-standards/find-codes-standards/b30-9-slings (checked November 2026)
Send the machine details
Type, size, weight, where it is and where it is going. Photos help. Estimates are free.
Start the estimateLicensed in Nevada
Nevada State Contractors Board licenses 0046276 (C-33 Installing Industrial Machinery), 0083124 (A-14, A-20) and 0083125 (C-14I Rigging and Cranes, C-14J Conveyance of Goods). USDOT 642556, MC-531191.
What the classes coverAre these guides legal or engineering advice?
No. They describe what the public rules and standards say, in plain language, so you can ask better questions. Always read the cited source, and for a specific lift or permit follow the actual text and the agency that issues it.
Can ILS help with the machine in a guide?
Yes. ILS moves, rigs, hauls and installs machinery from its yard on Goni Road in Carson City, and estimates are free. Send the machine type, size, weight and addresses and the office takes it from there.
How often are the rules checked?
Each guide names the section it relies on. Statutes and regulations change, so confirm the current text at the linked source before you plan a job around it.
Free estimates
Tell us what needs moving.
Free estimates on every job, big or small. Call the office or send the machine details and we will call you back.
(775) 882-3319Monday to Friday, 7:00 am to 4:00 pm. Fax (775) 882-2693.
- Nevada Contractors License 46276
- USDOT 642556 · our own trucks
- Carson City since 1999
- 4.6 on Google (15 reviews)
