300-ton hydraulic gantry system
ILS lists a 300-ton hydraulic gantry system for lifting very heavy machinery straight up and setting it down in a controlled way. It is the tool we look to when a load is too heavy, too tall or too awkward for a forklift, or when there is no overhead crane in the building.
- Nevada Contractors License 46276
- USDOT 642556 · our own trucks
- 4.6 on Google (15 reviews)
Key points
- Published equipment: a 300-ton hydraulic gantry system
- Lifts heavy machines straight up without an overhead crane
- Works inside buildings and in yards where headroom or access is limited
- Planned around floor strength, track path and the load's center of gravity
- Free estimates from weight, size and route
A gantry is a frame that straddles the load. Hydraulic jacks or lifting units on the frame raise the machine a little at a time, and the frame can be moved on tracks or rollers to carry the load to where it goes. Industrial Logistics Services lists a 300-ton hydraulic gantry system among its equipment, and ILS has the capacity of moving and relocating equipment weighing up to 300 tons.
How a hydraulic gantry works
The frame has two sides and a beam across the top, like a goalpost, set so the machine sits between the legs. Hydraulic cylinders lift the load in slow, even steps, and the operator can hold it at any height. Because the lift is hydraulic and controlled, a very heavy machine can be raised, shifted and lowered without the swing that comes with a hook on a moving boom.
Once the machine is up, it can be rolled on skates or the gantry's own track system to a trailer, a new location or a foundation. This is slow work by design, and slow is how a heavy load stays under control.
When a gantry is the right tool
- The load is heavier than a forklift with a rigging boom should lift
- The building has low headroom, a weak roof or no crane
- The machine needs to be lifted and set onto a foundation with fine control
- Floor or ground access makes a mobile lift unsuitable
- The load is tall or has lifting points that sit far apart
For lighter lifts in tight spaces our 2-ton portable aluminum gantry is the smaller option, and forklifts with rigging booms cover most day-to-day lifting.
Planning a gantry lift
The planning is where the safety is. We need the true weight, not an estimate, and the position of the center of gravity. We then check what the gantry's legs will stand on, because a point load from a leg or track can be many times the load on the machine's own footprint. Floor slabs, basements, trench covers and utilities below the slab all matter (see our guide on floor loads and foundations).
The ASME B30 series of standards covers rigging equipment, including slings, rigging hardware and the jacks, rollers and gantries used to handle heavy loads. We cite it by name as the reference point for good practice.
After the lift
Once the machine is down, the next step may be leveling and alignment. The same company can carry on into machine installation and precision alignment, so there is no hand-off between a rigger and an installer.
Sources (3)
- ASME: asme.org/codes-standards/find-codes-standards/b30-1-jacks-industrial-rollers-air-casters-h (checked November 2026)
- U.S. Occupational Safety and Health Administration: osha.gov/laws-regs/regulations/standardnumber/1910/1910.184 (checked November 2026)
- U.S. Occupational Safety and Health Administration: osha.gov/laws-regs/regulations/standardnumber/1926/1926.251 (checked November 2026)
Send the machine details
Type, size, weight, where it is and where it is going. Photos help. Estimates are free.
Start the estimateLicensed in Nevada
Nevada State Contractors Board licenses 0046276 (C-33 Installing Industrial Machinery), 0083124 (A-14, A-20) and 0083125 (C-14I Rigging and Cranes, C-14J Conveyance of Goods). USDOT 642556, MC-531191.
What the classes coverWhat is the capacity of the gantry?
ILS lists a 300-ton hydraulic gantry system. The usable lift on a particular job depends on the load, the lift points and the surface, and is confirmed in the plan.
Can the gantry work indoors?
Yes, where the floor can carry the legs and track loads and there is enough width and height for the frame. We check both before the day of the lift.
How do I know if my machine needs a gantry?
Send the weight, size and photos of where it sits. We will tell you whether a forklift with a rigging boom, a gantry or skates is the right method.
Free estimates
Tell us what needs moving.
Free estimates on every job, big or small. Call the office or send the machine details and we will call you back.
(775) 882-3319Monday to Friday, 7:00 am to 4:00 pm. Fax (775) 882-2693.
- Nevada Contractors License 46276
- USDOT 642556 · our own trucks
- Carson City since 1999
- 4.6 on Google (15 reviews)
