Commercial safe and vault moving
A commercial safe is moved on skates or a low dolly, lifted with a forklift boom or a gantry when it has to go up or down, and set on a floor that has been checked for load. ILS rigs and moves commercial safes, vault doors and security cabinets for banks, offices and stores, and other businesses.
- Nevada Contractors License 46276
- USDOT 642556 · our own trucks
- 4.6 on Google (15 reviews)
Key points
- Banks, offices, stores and similar businesses
- Weight and footprint are checked against the floor before the move
- Locks and relockers are handled by a locksmith or the safe company
- Safes are moved upright on skates unless the maker says otherwise
- Free estimates from the model plate, photos and a floor plan
Commercial safes are some of the densest objects a building holds. Office safes are heavy for their size; the weight is on the plate or in the maker's literature; bank-grade safes, vault doors and depository units weigh far more. The weight sits in a small footprint, which puts a load of pounds per square foot onto a floor that ordinary construction may not carry.
Weight and floor loading
The weight of a safe is on its plate or in the manufacturer's literature. Typical office and business safes are heavy for their size, and fire-resistant models carry insulation that adds weight. Vault doors and modular vault panels weigh far more. The safe's weight is concentrated in a small area, so the floor under it, the route to it and any ramp must be checked. A structural engineer can confirm a slab or an upper floor.
On a ground-floor slab, plywood and steel plates spread the load during the move. Upstairs, a safe may be hoisted from outside instead of moved through the stairwell.
How a safe is moved
Safes are moved upright with machinery skates and low-profile dollies, using bars and jacks to get under the base. Where a safe must change levels, a forklift with a rigging boom, a hydraulic gantry or hoisting equipment does the lift. Our general rigging work follows the same lift-planning steps used on machine tools.
- Confirm the model, weight and dimensions
- Measure doors, hallways, corners and thresholds
- Check floor capacity and lay protection
- Skate or hoist the safe along the planned route
- Set it in the new position and check it is level and plumb
- The owner's locksmith or safe company reprograms the lock if needed
Doors, locks and relockers
A safe door with a boltwork and a relocker is a mechanism that can lock itself if the safe is tilted or shocked. A locksmith or the safe company should be on hand, or should be told of the move in advance, and the combination should be known. Opening, drilling or changing a lock is work for a locksmith or the safe company.
Anchoring
Many commercial safes are bolted to the floor. Anchoring into a concrete slab is a construction task, and permanently attaching equipment to a structure falls under Nevada's contractor licensing rules (NRS 624). ILS holds C-33 Installing Industrial Machinery and A-14 licenses; ask about anchoring when you request an estimate.
What to send
Send a photo of the safe and its plate, the dimensions, the weight, the start and end locations, and a photo of the route including steps or ramps. Estimates are free.
Sources (4)
- U.S. Occupational Safety and Health Administration: osha.gov/laws-regs/regulations/standardnumber/1910/1910.178 (checked November 2026)
- U.S. Occupational Safety and Health Administration: osha.gov/laws-regs/regulations/standardnumber/1910/1910.184 (checked November 2026)
- ASME: asme.org/codes-standards/find-codes-standards/b30-9-slings (checked November 2026)
- Nevada Legislature: leg.state.nv.us/nrs/nrs-624.html (checked November 2026)
Send the machine details
Type, size, weight, where it is and where it is going. Photos help. Estimates are free.
Start the estimateLicensed in Nevada
Nevada State Contractors Board licenses 0046276 (C-33 Installing Industrial Machinery), 0083124 (A-14, A-20) and 0083125 (C-14I Rigging and Cranes, C-14J Conveyance of Goods). USDOT 642556, MC-531191.
What the classes coverWho should call about a safe move?
ILS moves commercial safes and vaults; call the office about any safe move.
Who opens or rekeys a safe?
Opening, drilling or changing a lock is work for a locksmith or the safe company.
How do you protect the floor?
With plywood and steel plates over the route and at the final position. The owner confirms the floor capacity for the safe's weight.
Free estimates
Tell us what needs moving.
Free estimates on every job, big or small. Call the office or send the machine details and we will call you back.
(775) 882-3319Monday to Friday, 7:00 am to 4:00 pm. Fax (775) 882-2693.
- Nevada Contractors License 46276
- USDOT 642556 · our own trucks
- Carson City since 1999
- 4.6 on Google (15 reviews)
