3868 Goni Rd, Carson City, Nevada 89706Fax: (775) 882-2693Nevada Contractors License 46276Phone: (775) 882-3319
Industrial Logistics Services badgeIndustrial LogisticsServices, Inc.Machinery moving & installation(775) 882-3319

Moving presses and press brakes

A press or press brake is moved by securing its ram and bed, dealing with hydraulic and pneumatic energy before disconnecting, lifting from the frame and setting it on a foundation or pads. ILS has the capacity of moving and relocating equipment weighing up to 300 tons and holds a 300-ton hydraulic gantry system for large frames.

  • Nevada Contractors License 46276
  • USDOT 642556 · our own trucks
  • 4.6 on Google (15 reviews)

Key points

  • The ram is blocked or pinned before the machine is lifted
  • Hydraulic and air energy is released under the plant's lockout program
  • Tall frames are checked for center of gravity before the pick
  • Foundations and pits are inspected before the new set
  • A 300-ton hydraulic gantry system is on the equipment list
  • Free estimates

Stamping presses, hydraulic presses, shears and press brakes are tall, heavy and top-heavy, and they are built around a rigid frame that has to be put back exactly. Some stand on their own foundations or in pits. Industrial Logistics Services plans these moves from the Carson City yard for fabrication shops, plants and schools.

What makes a press hard to move

A press concentrates its mass high in the crown and the ram. Lift it from the wrong place and the machine can tip, so riggers work out the center of gravity first. Many presses are also bolted to a foundation, sometimes grouted, sometimes sitting in a pit. Getting the machine loose can be as much work as lifting it.

Press brakes are long and narrow, with a heavy bed and ram and side frames that can be damaged by a sling pressing on them. Their back gauges and controls are delicate.

Energy and safety before anything moves

A press can hold energy in a flywheel, an accumulator, a hydraulic line or a counterbalance cylinder. OSHA's rule for mechanical power presses is 29 CFR 1910.217, and the general lockout rule 29 CFR 1910.147 requires energy to be controlled before service. The plant, not the mover, owns the lockout program, and we work with it. See the lockout/tagout guide.

  • Pin or block the ram so it cannot drop
  • Release stored hydraulic, air and counterbalance pressure as the maker directs
  • Drain hydraulic oil if the maker or the haul requires it
  • Cap the lines and label hoses
  • Remove dies, bolsters and loose tooling and move them separately

Moving and setting

Frames that can be forked are moved with a forklift and rigging boom. Heavy frames and presses on foundations are lifted with slings and a hydraulic gantry or placed on machinery skates. The load is chained to a lowboy and the haul follows Nevada size limits; wide or tall presses may need an NDOT permit. Our oversize permit guide explains the thresholds.

At the new location the foundation has to be ready first: size, anchor bolts, floor load and flatness. ILS offers engineering services and foundations as part of a relocation project. The floor loads and foundations guide covers the questions to ask.

Leveling and reconnecting

Presses are leveled on their pads or foundations with optical levels and spirit levels, since a press out of level can wear its gibs and guides. Who reconnects power is agreed in the estimate, and the maker's technician checks parallelism and clutch or valve function before production.

What to send for an estimate

Send the weight and the overall dimensions, photos of the press and the foundation, the path out and the location where it will go. A photo of the nameplate saves time. Estimates are free.

Sources (3)

Send the machine details

Type, size, weight, where it is and where it is going. Photos help. Estimates are free.

Start the estimate

Licensed in Nevada

Nevada State Contractors Board licenses 0046276 (C-33 Installing Industrial Machinery), 0083124 (A-14, A-20) and 0083125 (C-14I Rigging and Cranes, C-14J Conveyance of Goods). USDOT 642556, MC-531191.

What the classes cover

FAQ

Questions we hear

All questions

Can you move a press that is bolted to a foundation?

Yes. The anchors are released and the press is lifted off with the method that fits its weight. The new foundation needs to be ready before it arrives.

Who handles the lockout?

Lockout is the plant's own program. Who does the disconnect and reconnect is agreed in the estimate, and ILS coordinates the timing.

How big a press can you move?

ILS has the capacity of moving and relocating equipment weighing up to 300 tons. The method comes out of the estimate.

Free estimates

Tell us what needs moving.

Free estimates on every job, big or small. Call the office or send the machine details and we will call you back.

(775) 882-3319

Monday to Friday, 7:00 am to 4:00 pm. Fax (775) 882-2693.

  • Nevada Contractors License 46276
  • USDOT 642556 · our own trucks
  • Carson City since 1999
  • 4.6 on Google (15 reviews)

Request a free estimate

Your details
The machine

Up to 8 photos. Big photos are resized on your device before they are sent.

Free estimates. Your details go only to Industrial Logistics Services. We call back Monday to Friday, 7 am to 4 pm.