7 min read · Updated November 2026
Nevada oversize load permits explained
In Nevada a load that exceeds 14 feet in height, 70 feet in combination length or 102 inches in width needs a permit from the Nevada Department of Transportation, as do loads above the federal 80,000-pound limit. Permits come as single-trip or annual multiple-trip, and the load must be non-reducible.
- Nevada Contractors License 46276
- USDOT 642556 · our own trucks
- 4.6 on Google (15 reviews)
Key points
- Legal height is 14 feet (NRS 484D.605); combination length is 70 feet (NRS 484D.615)
- Width over 102 inches needs a permit (NRS 484D.725)
- Weight above the federal 80,000-pound limit also needs an over-dimensional permit
- Single-trip permits fall under NAC 484D.655 and annual permits under NAC 484D.660
- The permit names the vehicle, the load and the exact highways (NRS 484D.730)
Moving a machine across Northern Nevada usually means a truck and a trailer. Most machines fit inside the legal envelope, but tall presses, wide tanks and long processing lines do not. This guide summarizes the rules in the Nevada Revised Statutes and Administrative Code that matter for machinery, so you know early whether your move needs a permit. It is a plain-language reading, not legal advice.
The numbers that trigger a permit
Nevada sets the maximum size of a vehicle and its load in NRS chapter 484D. Anything beyond these limits is an oversize or over-dimensional load and moves only with a permit from the Nevada Department of Transportation (NDOT).
| Measure | Limit without a permit | Where it comes from |
|---|---|---|
| Height | 14 feet | NRS 484D.605 |
| Length of a combination | 70 feet | NRS 484D.615 |
| Width | 102 inches | NRS 484D.685 |
| Gross weight | 80,000 pounds (federal limit) | 23 CFR 658.17 |
Some axle and bridge limits also apply on specific highways, and a few road segments have lower clearances. Confirm the details with NDOT for your route.
What non-reducible means
A permit is only issued for a load that cannot reasonably be made smaller. NAC 484D.650 calls this a non-reducible load. A machine that can be split into legal pieces by removing a table, a head or a guard must usually travel in those pieces. A one-piece press, a boiler shell or a tank is non-reducible, and so is a machine whose parts cannot be separated without damage. This is one reason the preparation and disassembly steps in preparing a machine for moving matter on the road as well as inside the plant.
Single-trip and annual permits
NDOT issues two main types through its Over Dimensional Vehicle Permits office. A single-trip permit (NAC 484D.655) covers one movement of one load along stated roads. An annual multiple-trip permit (NAC 484D.660) covers repeated movements of a vehicle or load that stays within stated size limits. Most one-time machinery relocations use single-trip permits. The permit lists conditions, which can include travel windows, escort vehicles and route limits.
What the application describes
The application must describe the vehicle, the load and the exact highways to be used (NRS 484D.730). That is why measurements matter. The carrier needs the machine's overall length, width, height and weight, the trailer's deck height and length, and the axle configuration. Trailers to 50 tons can carry most machines, but a lowboy deck still adds height to the load. Use the oversize load checker to see where a load stands, and the legal load limits table for the numbers side by side.
What happens beyond the permit
Large loads may also need escort vehicles. NAC 484D.670 sets when a lead car or a rear car is required; the triggers are covered in when a Nevada oversize load needs pilot cars. A load that crosses the state line needs the permits of each state, and moving machinery into California covers the Caltrans side. Within Nevada, the carrier is responsible for following the permit's conditions.
How this affects planning a move
Treat the road as part of the plan from the first call. If you tell ILS the machine's size and weight in the request, the office can tell you whether the load is likely to fit inside the legal envelope on a given trailer or whether to plan for a permit. The permit is a separate step from the lift and the haul, and it goes faster when the information is accurate. The full job sequence is in how a machinery move works.
Sources (3)
- Nevada Legislature: leg.state.nv.us/nrs/nrs-484d.html (checked November 2026)
- Nevada Legislature: leg.state.nv.us/nac/nac-484D.html (checked November 2026)
- Electronic Code of Federal Regulations: ecfr.gov/current/title-23/section-658.17 (checked November 2026)
Send the machine details
Type, size, weight, where it is and where it is going. Photos help. Estimates are free.
Start the estimateLicensed in Nevada
Nevada State Contractors Board licenses 0046276 (C-33 Installing Industrial Machinery), 0083124 (A-14, A-20) and 0083125 (C-14I Rigging and Cranes, C-14J Conveyance of Goods). USDOT 642556, MC-531191.
What the classes coverDo I need a permit to move an oversize machine in Nevada?
Yes, if the loaded truck is over 14 feet high, 102 inches wide or 70 feet in combination length, or over 80,000 lbs. gross. NDOT issues single-trip and annual over-dimensional permits for loads that cannot be reduced (NRS 484D.605, 484D.615 and 484D.725; NAC 484D.650-.660).
Do I need a permit for a load over 102 inches wide?
Yes. NRS 484D.725 requires an NDOT permit for a vehicle or load wider than 102 inches. The permit conditions will also say whether escort vehicles are required.
Can I get one permit for several moves?
An annual multiple-trip permit under NAC 484D.660 exists for repeated movements within stated limits. Whether it fits depends on your loads, so check the rule or ask the permit office.
Who applies for the permit?
The motor carrier moving the load applies, using the machine's measurements and weight. Giving accurate numbers up front keeps the application correct.
Free estimates
Tell us what needs moving.
Free estimates on every job, big or small. Call the office or send the machine details and we will call you back.
(775) 882-3319Monday to Friday, 7:00 am to 4:00 pm. Fax (775) 882-2693.
- Nevada Contractors License 46276
- USDOT 642556 · our own trucks
- Carson City since 1999
- 4.6 on Google (15 reviews)
