Step deck trailer
A step deck trailer is a flatbed trailer whose deck drops down in one step behind the front section. The lower deck gives a tall machine extra room under Nevada's 14 foot height limit.
- Nevada Contractors License 46276
- USDOT 642556 · our own trucks
- 4.6 on Google (15 reviews)
Key points
- Two decks: a raised front deck and a lower main deck
- The lower deck buys height clearance for tall machines
- Nevada's legal height limit without a permit is 14 feet (NRS 484D.605)
- ILS lists multiple flat bed and step deck trailers among its equipment
- Loads still need tie-down points and a plan for width and weight
Height is the number that catches most machinery moves. A press, a compressor skid or a packaged unit can be narrow enough for the road yet too tall once it sits on a standard flatbed. The step deck solves that by putting the load closer to the pavement for most of its length.
How a step deck is built
The front deck sits over the tractor's fifth wheel and is the higher of the two. Behind it the deck steps down to the main deck, which carries most of the cargo. Ramps are sometimes used to drive or winch wheeled and tracked equipment up from the ground.
- Upper deck: short, over the tractor
- Main deck: long and low, where the machine rides
- Rear: ramps or a flat tail, depending on the unit
Step deck, double drop and lowboy compared
The three types are close relatives. A step deck has one drop. A double-drop trailer has a high front, a low well in the middle and a high rear over the axles, which gives the most height room for the load in the well. A lowboy is the low-deck family that includes detachable-neck designs such as the removable gooseneck.
| Trailer | Deck layout | Typical reason to choose it |
|---|---|---|
| Flatbed | One level | Short, low, wide loads that are easy to strap |
| Step deck | One drop | Machines a little too tall for a flatbed |
| Double drop | High, low well, high | Tall machines that need the lowest deck |
Where it fits on a Northern Nevada move
Many moves out of Carson City, Reno and Sparks start with a machine that has to clear freeway overpasses and the grades of US-395 and I-80. Picking a deck with the right height is cheaper than applying for a permit that was not needed. Our oversize load checker shows where height, width and length limits sit.
Industrial Logistics Services lists multiple flat bed and step deck trailers, single-drop and double-drop equipment trailers to 50 tons, and removable gooseneck and beaver trailers to 50 tons. Which trailer carries your machine is settled during the free estimate, from its size, weight and route.
Sources (3)
- Nevada Legislature: leg.state.nv.us/nrs/nrs-484d.html (checked November 2026)
- Nevada Legislature: leg.state.nv.us/nac/nac-484D.html (checked November 2026)
- Federal Motor Carrier Safety Administration: fmcsa.dot.gov/regulations (checked November 2026)
Send the machine details
Type, size, weight, where it is and where it is going. Photos help. Estimates are free.
Start the estimateIs a step deck the same as a lowboy?
No. A step deck has a single drop and a lowboy has a deeper, lower deck. Both are used to keep tall loads under legal height, and the choice depends on the machine's height and weight.
Does a step deck load still need a permit?
It can. A load over 14 feet high, 70 feet long or 102 inches wide needs an over-dimensional permit from NDOT, and a heavy load can need one on weight alone.
Free estimates
Tell us what needs moving.
Free estimates on every job, big or small. Call the office or send the machine details and we will call you back.
(775) 882-3319Monday to Friday, 7:00 am to 4:00 pm. Fax (775) 882-2693.
- Nevada Contractors License 46276
- USDOT 642556 · our own trucks
- Carson City since 1999
- 4.6 on Google (15 reviews)